Home/Shop
    • Clamps only on the extension tube
    • Attach Flashlights, Lasers, Sling mount points directly to your Extension tube without hindering your shotguns point of aim
    • 6061 Aluminum, mil spec rail
    • Works with Taccom, Nordic, & RCI extension tubes
    • For Benelli M1, M2, SBE, SBE2 and M3 Shotguns
    • Quicker way to activate bolt release

    Join the waitlist to be emailed when this product becomes available

    • 7% discounted bundle
    • Package includes:
      • VR80 ambidextrous charge handle
      • VR80 extended mag release
      • VR80 safety selector
    • Comes in Black

    Join the waitlist to be emailed when this product becomes available

    • 7% discounted bundle
    • Package includes:
      • VR80 Muzzle brake
      • VR80 Handguard retainer
    • Comes in Black
    • 7% discounted bundle
    • Package includes:
      • VR80 recoil buffer
      • VR80 Flat wire spring
      • VR80 buffer tube
    • Comes in Black

    Join the waitlist to be emailed when this product becomes available

    • Light Weight 3oz
    • Made from 6061 aluminum
    • Black anodized
    • Threads on barrel
    • Brass set screw will not damage barrel threads
    • Comes with split retainers
    • Hand guard slips over brake for cleaning gas system
    • Allows for choke tube removal
    • Eliminates the barrel nut/shroud
    • Works with short and long VR80 hand guards
    • Low profile, does not interfere with sighting
    • Makes your hand guard float
    • Increased slug accuracy
    • Made from 6061 aluminum
    • Anodized black
    • Installs with ease
    • 6.5” long
    • Snaps over factory hand guard
    • Held in place with 3M VNB tape
    • Shields your hand from hot gases
    • Rough grip surface
  • VR80 Extreme Charger

    $39.95$42.95
    • Ambidextrous design
    • Positive non-slip grab
    • Will not come out under fire
    • Stainless steel hardware
    • Lightweight 1.2 ounces
    • Non-corrosive stainless steel cross bar
    • Machined Delrin handles w/finger grooves
    • Longer, wider and taller than factory
    • Available in Black or Blue Delrin
    • Comes with stainless and black oxide hardware
    • Works on either side of the factory safety barrel
    • Easy no gunsmithing install
    • Direct replacement
    • Works with factory selector levers
    • Works with TACCOM extended lever
    • Barrel only, use your existing fasteners
    • Provides for a shorter throw to disengage the safety
    • Works with aftermarket triggers
    • May shorten the over-travel on the factory trigger as well.
    • Extends out farther than factory
    • Very smooth almost effortless magazine release
    • Made out of Delrin
    • Uses factory hardware for install
    • Available in Black or Blue
    • 2 stage recoil system
    • Aluminum buffer
    • Internal 2nd stage, extended plunger
    • Reduces felt recoil
    • Works with factory recoil spring or modified AR15 carbine spring
    • Eliminates coil bind over factory system
    • Allows for use with Bolt Hold open
    • Does not come with recoil spring**
    • Chrome Silicon Spring
    • Improves Cycling and Overall Operation
    • Traditional Round wire spring
    • Fits factory VR80 buffer tube
    • Recommended for use with the TACCOM VR80 Recoil buffer
    • Chrome Silicon Spring
    • Improves Cycling and Overall Operation
    • Longer service life than round wire springs
    • Will NOT fit factory VR80 buffer tube
    • Will fit commercial buffer tube 

    Join the waitlist to be emailed when this product becomes available

    • 6 position carbine tube
    • Commercial spec
    • 6061-T6 Aluminum
    • Black Hardcoat anodize
    • Fits the VR80
    • Comes with Castle Ring and AR15 latch plate
    • Factory 19 round magazine spring
    • Works with all VR80 stick magazines
    • Works with TACCOM magazine extension
    • Adds 5 rounds to the factory 19 round magazine
    • Uses factory 19 round spring
    • Machined from Delrin
    • Easy assembly
    • Overlaps the parent magazine and will not come off
    • Push button, locking, belt attachment
    • Can mount holsters, shell caddies, mag pouches, you name it!
    • Made out of polymer nylon
    • Adjustable bar fits belts 1/4" to 2-1/4"
    • Raises Shell holders by as much as 1.5" on the belt
    • Works with all TACCOM shell holders
    • Works with Tek-Lok, TMMS and ELS hooks