-
- 16.25" legal rifle barrel (4.5" rifling)
- 10.2oz
- Drop in for all .920” applications
- 7/8" Black Carbon Fiber Shroud (pinned and cover welded)
- 22LR Sport Chamber
- Will not work with takedown models
- SHIPPING 12/12/25
-
Out of stock
- 16” Carbon Fiber shrouded barrel
- 5.25” effective 1:10 rifling
- Super feed barrel (no bolt modification required)
- Lightweight 13.5oz
- Replaces factory trunnion block
- STARTING TO SHIP ON MAY 14TH, 2025
-
Sale!
- 16” length, 4.5" effective rifling
- 11oz
- Barrel collar NOT included
- Chambered for 22 long rifle (22LR)
- 1:16 twist rate
- 416SS barrel
- Pin and welded, (.75" dia) brushed aluminum shroud
- Designed to be used with CMMG barrel collar (.460 dia spud)
- Will NOT work with M&P 15-22
-
Sale!
- 16″ legal length rifle barrel (4.5″ rifling)
- 416 ss barrel
- 12oz
- Pin and welded, stainless steel shroud (.75" diameter)
- 22LR Sport Chamber
- Uses factory barrel collar, ejector, and roll pins from factory barrel
-
Sale!
- 16.25" legal rifle barrel (4.5" rifling)
- 10.2oz
- Drop in for all .920” applications
- 416SS steel barrel
- 3/4” diameter pinned and welded carbon fiber shroud
- 22LR Sport Chamber
- Will not work with takedown models
- SHIPPING 12/12/25
-
- For .750" diameter barrels
- Steel construction
- Super effective
- Wrench flats provide tight fit
- Angle forward design
- Black Nitride Finish
- 3 oz
- 1/2 28 thread
-
Sale!Out of stock
- 8.0 oz
- 4.5” long
- ½-28 x .5” long thread
- 22LR Sport Chamber
- 416 Stainless Steel
- Will not work with takedown models
-
Sale!
- Allows you to use the Holosun 510C on your Browning Buck Mark
- 6061 material
- Black anodized
- Lowest possible mounting
- Just over 4oz with stripped optic
-
Sale!
- Mounts the 510C sight closer to bore
- Remove up to 4 ounces off the 510C
- Works on factory Ruger Receivers
- Comes with hardware to mount to receiver
- Black Anodized Aluminum
-
Sale!
- Allows you to use the Holosun 510C on your Ruger 22/45
- 6061 material
- Black anodized
- Lowest possible mounting
- Just over 4oz with stripped optic
-
Sale!
- 6061 material
- Silver finish
- Lowest possible mounting
- Just over 4oz with stripped optic
- Stainless hardware
- Includes a free ambidextrous side bolt racker with purchase!
-
Sale!Out of stock
- 8 position, extended buffer tube (A5)
- 3/4" spacer w/wave spring
- Adds a 2nd stage to your recoil system....or enhances the 2nd stage you already have
- 5 ports to allow excess water and gas to escape the operating system
- Machined from 7075-T6 Aluminum with a durable hard coat anodized finish
- Works with MBX, KynSHOT, Mil Spec buffers and more
- will not work with JP-SCS or any 'cartdrige style recoil systems
-
Sale!
- Use your trigger finger to engage/disengage safety
- Great for left handed shooters
- Replaces push button safety
- Works on Ruger 10/22 and Ruger PC Carbine
- .312” diameter Stainless safety barrel, delrin levers
- Can be installed while receiver is still in your stock
- Works with factory trigger group
- Check out our installation video below
-
Sale!Out of stock
- 8 position, extended buffer tube
- Compatible with the A5 Buffer System
- 5 ports to allow excess water and gas to escape the operating system
- Machined from 7075-T6 Aluminum with a durable hard coat anodized finish
-
- Black anodized aluminum
- Adds 8.25” to factory pistol barrel
- Overlaps factory barrel by .625” for a strong connection
- Extension weighs 2oz
- Makes the 1522P barrel a legal 16” rifle barrel
- Must be attached permanently per ATF guide lines
- **Can purchase the extension or send in your 1522P for modification (scroll down to learn more)
-
- Modification cost: $50 per barrel
- 16" non-fluted Tippmann barrels only
- Removes over 1lb of weight**
- How to get started:
- Send your barrel to us with cash or check
- (please make checks payable to "Taccom")
- We modify your barrel (1-2 day window)
- We ship it back with tracking if email is provided
- Send your barrel to us with cash or check
- For USPS please send to: PO BOX 431, Dassel, MN, 55325
- For UPS/FedEx please send to: 131 Parker Ave W, Dassel, MN, 55325
-
Out of stock
- Works with the 8up Gemini shell holders
- Assemble 1, 2, 3 or more 8up on the web belt
- Have 8, 16, 24 or 32 rounds on your chest.
- Convenient shoulder strap keeps everything in place
-
- Completely replaces the factory bolt release
- Extended out and back
- Made out of 6061 aluminum
- Black anodized
- *Will NOT work with ARV*
-
- 3/4” aluminum cushion
- 25# wave spring, .62” travel
- Designed for the S&W Response using the TACCOM adjustable 9mm buffer
- Will also work with the TACCOM ESSB Bolt and the TACCOM adjustable 9mm buffer combination
- Includes (2) optional 3/8” spacers, aluminum cushion and wave spring
-
- works with the 9MM FPC only
- Replaces factory end plug
- Helps reduce felt recoil
- Delrin (polymer) construction
- Allows for BHO to function
- Easy installation
-
Sale!Out of stock
- 3" diameter x 7 1/8" tall
- holds up to 250 rounds of 22rf ammo
- 3d printed
- engineered to be strong
- 'bullet' cap unscrews
-
Sale!Out of stock
- works on the 9mm, 10mm and 40sw FPC
- Lightweight, not bulky, fits the Rifle nicely
- High strength DELRIN polymer
- Adjustable for Length of Pull
- Butt Plate can be angled to fit in the ‘pocket’ of your shoulder
- Butt Plate has an aggressive texture will stay put!
- Aluminum QD swivel mount installed
- Comes with Assembly Hardware
- Retains the factory recoil system
- SHIPPING 3/27/26
-
Out of stock
- Under 6 ounces
- Lightest, most affordable carbon fiber handguard on the market
- Fire retardant
- Attaches to the included barrel nut with one machine screw (yes, the fit is that nice)
- Use's a standard Armorers wrench for installation to the upper receiver
-
- Length of pull from 10.5" to 15”
- Butt Plate adjusts up/down and rotational
- Adjustable cheek riser
- Aluminum/Delrin construction
- Ambidextrous design allows for right or left handed shooters
- "M&P" variation slips over the 15-22 ‘faux’ tube
- "M&P" variation will also fit MILSPEC carbine buffer tubes (1.14”)
-
- Keeps your Chest Rig from slipping down during a stage
- Option to direct mount to backer plate
- Works with ALL Taccom Chest Rigs
- Also works with our competitor's chest rigs that use up to 2" wide nylon belts
-
- Strap made out of nylon
- Attaches to your belt or belt loop for faster access
- Chamber flag made to universally fit all kinds of competition guns
-
For use with:
- TACCOM LW Carbine Recoil System
- Any Factory Carbine Recoil System
-
- Air cushioned on the recoil stroke for the last 1” of travel
- Wave spring enhances the 2nd stage to further reduce felt recoil and muzzle rise
- Designed to be used with the A5 length buffer tube
- Buffer weight – 5oz
- Developed mainly for 115, 124, and 147 grain loads (but will work with others too)
- Factory sealed air cushion, no maintenance required
- Spring loaded 3rd stage cushion softens return stroke
- Aluminum construction air cushion
- Custom flat wire spring
- Short Stroke System, eliminates BHO capabilities in some cases
- Not for use with Colt mag fed lowers
- Also designed to work with the S&W Response.
-
For use with:
- TACCOM LW Rifle Recoil System
- TACCOM ALW Rifle Recoil System
- Any Factory Rifle Recoil System
-
Sale!
- Black Nitride finish
- Pivoting Extractor
- Low drag, low weight key
- 13.5oz
- Works with both Glock magazines*
- Allows for the Bolt hold open to function with a shorter stroked rifle.
- Faster trigger reset
- Comes with longer spacers to help shorten your stroke
- COMPLETE READY TO DROP IN w/firing pin, extractor, key, etc.
- SHIPPING DEC. 10, 2025
-
- All variations come with a spring
- Machined Aluminium and anodized black
- Comes with tube of choice, spring, and end cap
- These tubes ONLY work with Taccom Extreme Extension nuts
- Nuts sold separately
-
- Machined Aluminium
- Anodized black
- Made ONLY for Taccom Extreme Extension tubes and/or nuts
-
- Anodized Aluminum
- Made for 12 gauge
- Made only to work with Extreme Extension Tube
-
- 17-4 stainless steel
- Made for reliable shell feeding
- Works with any tube extension
-
- All variations come with a spring*
- Machined Aluminium and anodized black
- Threaded differently on both sides for a modular set up
- "Kits" variations come with tube of choice, spring, and end cap
- These tubes ONLY work with Taccom Extreme Extension nuts
- Nuts sold separately
-
- Full hard Stainless steel
- Precision laser cut
- Sharp edge for extracting unfired rounds
- Works with CMMG, Model 1, and others
- Will NOT work with M&P 15-22
-
Sale!
- WORKS WITH YOUR ICE FISHING POLE
- Stainless Steel Hardware (included)
- Orange, Yellow, Red or Black Tubes
- FULL RANGE OF MOTION
- Folds up out of the way for travel, no need to remove.
- ALLOW FOR UP TO 1 WEEK FOR SHIPPING
-
Sale!Out of stock
- WORKS WITH YOUR ICE FISHING POLE
- stainless steel hardware (included)
- 3d printed parts and over built
- takes down for easy carry
- adjustable trigger tension
- ALLOW FOR UP TO 1 WEEK FOR SHIPPING
- YouTube short showing the function
- https://www.youtube.com/watch?v=rk-wDHU3hc8
-
Sale!Out of stock
- Made out of BLACK Carbon Fiber
- Aluminum barrel nut
- Small diameter for better grip
- 14.5" length
- 6oz total weight
- Works great with ULW barrels
- MLOK slots
- Blow back actions only!
-
- Made out of TITANIUM
- No sharp internal corners
- Stress relieved
- Works with Taccom, Faxon, and Surmount bolts
-
- Chrome Silicon Spring
- Improves Cycling and Overall Operation
- Longer service life than round wire springs
- Spring works in carbine and rifle buffer tubes
-
Sale!
- Made universally for Mossberg 590/590A1 and Remington 870; TAC-14
- 80 Grit
- Made by 3M
-
- HIGH VISIBILITY
- NO DRAG
- fully machined follower, made from acetal (Delrin)
- 12 gauge pumps, semi-auto shotguns
- 2 models: friction free or friction free Nova/Vinci
-
Sale!
- Steel blade, black oxide coated
- Comes with green and red fiber optic
- Mil spec A2 sight height
- .06" diameter fiber optic front sight
-
- Black anodized 6061 Aluminum
- Mounts directly to barrel
- Picatinny Rail Spec
- Same Height as Rear Factory Rail
- Allows for use of detachable iron sights
- Uses factory screws to mount
- Designed to only work with rear factory rail
-
Sale!Out of stock
- Black anodized aluminum
- Light weight
- Picatinney rail mount
- Compression fit on barrel
- Set same height as receiver rail
-
- 11” or 16” fully rifled barrel
- 1:16” twist
- Chambered for 22 long rifle
- Threaded ½-28 (3/4” barrel end contour)
- Will work with CMMG barrel collar (.46 dia spud)
- Designed to work with TACCOM 22rf bolt assy
- Will NOT work with M&P 15-22
- BARREL COLLAR NOT INCLUDED
-
Sale!Out of stock
- WORKS WITH THE FACTORY POLE
- stainless steel hardware (included)
- 3d printed parts and over built
- easy depth set adjustment
- folds for easy carry
- transducer mount not included
- ALLOW FOR UP TO 1 WEEK FOR SHIPPING
-
- Enhances Feeding Reliability
- Stainless Steel
- Removable
- Minimal fitting required upper can be modified with a small file
-
Sale!
- Originally made for Mossberg 590 Shockwave and Remington TAC-14
- Can be used as generic handguard grip
- 80 Grit
- Grips made by 3M
-
Sale!
- only works with the 9mm OR 10mm FPC
- Light weight 1.1 ounces
- Black anodized aluminum finish
- Attaches with a 7/8” wrench (9MM) OR set screws (10MM)
- Allows the use of any AR15 hand guard nut
- hand guard and/or hand guard nuts are NOT included
-
- 80 grit
- Made by 3M
- MLOK comes with 10 pieces (x8 4.7" | x2 solid)
-
- Machined Aluminium
- Threading fits the standard AR15 platform
- Blowback AR style only! (PCC, 22)
-
Sale!
- Provides a positive hand stop
- MLOK design
- 3/4” diameter x 1” long
- Small foot print, compact
- Smooth and comfortable
-
Sale!
- works with 9MM, 10MM and 40SW FPC
- Replaces the factory charge handle
- Allows for solid, hassle free charging
- 'Hook' and charge with authority using one finger
- Allows for charging weapon with shorter magazines inserted in factory buttstock
- Eliminates the fold/lock feature
- Will not break
- the 2 cocking handles can be placed in any of the 3 tapped holes
-
Sale!Out of stock
- 39" Black Carbon Fiber Tube
- stainless steel hardware
- 3d printed parts and over built
- easy depth set adjustment
- folds for easy carry
- transducer mount not included
- ALLOW FOR UP TO 1 WEEK FOR SHIPPING
-
- Developed specifically for the JP Enterprises JP5 carbine
- Air cushioned on the recoil stroke for the last 1” of travel
- Wave spring enhances the 2nd stage to further reduce felt recoil and muzzle rise
- MUST BE USED with an A5 length buffer tube
- Buffer weight – 1oz
- Factory sealed air cushion, no maintenance required
- Aluminum construction air cushion
- Custom flat wire spring
- Allows for the use of BHO and LBHO
- SHIPPING 01/31/25
-
- Super fast magazine changes
- Simple installation
- Stainless steel post
- Large button
-
Sale!
- Designed for carbine buffer tube length
- For use in blow back actions only
- Comes an AR15 flat wire spring
- 6.5 ounces
- 2 stage action
- Allows for the BHO/LRBHO to function
